Articles, Blog

Table Tennis Booster Tutorial (English Narrated Version)

January 21, 2020


Today we will show you how to apply booster
oil on a table tennis rubber The rubber we used today is hurricane 3,
this is a very common rubber to be used with booster After applying the booster,it can increase the speed,spin
and most importantly enhancing the feeling of ball control. There are many different types of booster in the market,we
will use this one. this one can last for around three months. First we brush a thin layer of glue onto the rubber Then we let it try Then we start applying the booster It is just like brushing the glue Make sure you don’t too much, otherwise,
bubbles will form . so a thin layer is just right. After finishing a layer, you should let it dry and
wait for twelve hours(or one day). You should let it completely dry before
you put on another layer Some people think two layers are enough.
Others think that it is still not soft enough,
and may put more layers.
But we do’t recommend putting more than 3 layers. You can see the rubber is now curved.
We can now put on another layer. It is just like the first time.
Brush it evenly. After finishing, you can let it dry. Then we can glue the rubber to the blade This is the 3rd day. Though it is already dry,
but it is two curly. So we recommend waiting
for another day before gluing the rubber Now we see the rubber is flatter now,
therefore, we can start gluing the rubber to the blade After putting on the glue,we then let it dry It is just like the normal gluing procedure Now we put the rubber to the blade. You see, the rubber actually becomes larger.
So we cut the extra rubber. To sum up, the booster can enhance the speed,
spin and feeling of ball control. Now it is finished and it can be used right away

41 Comments

  • Reply Yu Hang Fang March 30, 2014 at 4:44 am

    成功需苦真幹、原來塗膨脹劑要搞幾日

  • Reply Jane KWOK April 6, 2014 at 4:58 am

    It really takes some steps. But sometimes it is worth.

  • Reply Jane KWOK April 6, 2014 at 4:58 am

    It really takes some steps. But sometimes it is worth.

  • Reply Ping PongProTips April 10, 2014 at 10:58 pm

    Is this legal for competition

  • Reply Ye Liu April 14, 2014 at 6:48 am

    I am trying to the steps, after 2nd layer, I have already waited for 2 days, the rubber is still very curly! What have I done wrong? Can I glue it even if it's very curly?

  • Reply CipheR June 9, 2014 at 4:10 am

    If I'm boosting a new Hurricane 3 neo, do I remove the glue like layer on the sponge before applying the WBG or WSG and the booster? 

  • Reply Edmund Ng July 5, 2014 at 3:00 pm

    Yes it is legal for competition. I used it once and passed the test.

  • Reply crbn September 6, 2014 at 5:46 pm

    Since you are from Asia, can you tell me if there really exist the Commercial, Provincial and National versions? Or just the sellers pretend they exist and just want to make more money. Thanks.

  • Reply ferdav25 November 13, 2014 at 12:43 pm

    booster after glue ?????? wtf….

  • Reply Fa'iq Shafik June 15, 2015 at 5:34 am

    Thank you for the instructional video. Doing my second set of rubbers (DHS H3N & Yinhe Moon). The effect is still there on my other blade (now two months of use).

    For whoever contemplating in buying the product, the rubber becomes noticeably bouncier and spinnier.

    Please have patience while boosting the rubber, do not rush the process. Have fun!

  • Reply Pumsti 11 August 16, 2015 at 12:18 am

    why do you put a thin layer of glue on the rubber before you are adding the first layer of booster?

  • Reply GUSTAVOPINGPONG September 16, 2015 at 12:11 am

    I really dont like putting a layer of glue before the booster… I did it with a Hurricane 3 Neo and it felt like wet glue just before being ready to glue to the blade, didnt like the result. I unglued the rubber from the blade, peeled off the glue and glue again from dry, better result. Also, i dont feel the booster will get straight to the sponge if i put a layer of glue first interfering with the sponge-booster interaction

  • Reply Ddpan j October 12, 2015 at 11:40 am

    i ve applied the booster for the 2nd layer but my rubber still not curve since the first layer. already waiting for a day. am i did wrong ? i am using h8

  • Reply Karsten 0100010101101101010101000100010101001011 December 31, 2015 at 3:37 pm

    good thats right. better use Provincial or National Version of this Rubber

  • Reply Arkadi Danielyan January 15, 2016 at 10:02 pm

    nice blade

  • Reply Pablitorrinco January 26, 2016 at 2:46 pm

    but the sponge expand and lose a bit or hardness degree

  • Reply Red Motegi April 6, 2016 at 12:03 pm

    It's like listening to a fairy tale. Sleepy

  • Reply phiên nguyễn hoàng May 25, 2016 at 2:49 am

    Can you tell me how much does this falco tempo long booster cost?

  • Reply mendebil August 22, 2016 at 1:13 pm

    jesus that's 500 dollars worth booster on his desk?

  • Reply shogrran August 31, 2016 at 2:22 am

    So why not buy a soft rubber on the get-go? I still don't get the difference.

  • Reply Simba Sosa September 22, 2016 at 6:21 am

    what if u glue 5 hours after applying lol

  • Reply Nguyen Au November 7, 2016 at 7:24 am

    Thanks a lot!!!

  • Reply Angelo Lundström December 26, 2016 at 1:31 pm

    Hi, im out of glue so can i like use butterfly free chack first time before applying the booster…. then like nittaku finezip glue when gluing to the blade?… after the booster process? or do i need to just use one type of glue whole time?

  • Reply Angelo Lundström January 10, 2017 at 7:21 pm

    Can you glue the rubber when it is like a circle in shape? very curly and i waited now for 3 to 4 days

  • Reply Sheet of Paper January 24, 2017 at 1:15 pm

    what type of glue should we use

  • Reply iamjom 191 February 9, 2017 at 12:48 pm

    you have Facebook or something like that, I would like ask some questions about glue and booster.

  • Reply whatscreenname February 24, 2017 at 9:03 pm

    Why do you need to put a layer of glue first?

  • Reply てんめい March 4, 2017 at 9:24 am

    めちゃくちゃ補助剤置いてるじゃん

  • Reply FuriousGamer 876 March 19, 2017 at 10:56 pm

    against ittf rules this is like drugs for a race

  • Reply Gaudier Power March 22, 2017 at 5:59 pm

    where are your shop

  • Reply Viz muñiz June 23, 2017 at 6:26 am

    I forgot to put the glue before. is this a problem?

  • Reply Vladimir M August 29, 2017 at 1:30 pm

    how to remove booster ?

  • Reply riemikes December 25, 2017 at 3:03 am

    Not only can increase speed and spin, falco booster can take away the old glue that on sponge for long time. Just apply a layer of booster on your sponges, after 15 minutes, booster will soften the old glue and can be rub it out easily with out damage the sponge , especially good for those expensive tenergy. After remove old glue, just apply one more thing layer booster, then let it dry and reglue it back on your blade.

  • Reply daniel arellano January 25, 2018 at 1:32 am

    I need to cut the rubber first or I can do it after put the booster?

  • Reply 상어덮밥편의점 January 30, 2018 at 8:07 am

    I like her voice and English accent.

  • Reply shadowburnJr April 15, 2018 at 9:59 am

    Is it still legal?

  • Reply Wilyn Mansayon May 7, 2018 at 9:37 am

    Is that an already glued rubber? Just peeled of?

  • Reply Wilyn Mansayon May 7, 2018 at 9:38 am

    Does the rubber need to be new?

  • Reply ruby zapanza July 23, 2018 at 1:34 am

    how often would you apply booster on rubber and reglue?

  • Reply flagella1337 September 13, 2018 at 3:56 am

    hurricane tree

  • Reply Yafi June 15, 2019 at 9:15 am

    Watch this in 1.5x TRUST ME

  • Leave a Reply